This OMRON 3G3EV-ABMA-CUE SYSDRIVE Inverter is used and in excellent condition. Configurations: A: Panel Mounting Installation Type B. Omron SYSDRIVE 3G3EV SERIES Pdf User Manuals. View online or download Omron SYSDRIVE 3G3EV SERIES User Manual. View and Download Omron SYSDRIVE 3G3EV user manual online. Compact Low-noise Inverter. SYSDRIVE 3G3EV Inverter pdf manual download.
|Published (Last):||18 March 2016|
|PDF File Size:||18.99 Mb|
|ePub File Size:||20.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Chapter 3 Installing a Noise Filter on the Power Supply Side Install a noise filter to eliminate noise transmitted between the power line and the Inverter.
Page moron Chapter 3 Design Induction Noise: Constant settings are initialized. Page 51 Chapter 4 Preparing for Operation Operation after Recovery from Power Interruption Setting range 0, 1, 2 Factory setting 0 This constant is used to select the processing to be performed after recovery from an instantaneous power interruption. Chapter 4 c n31 electronic thermal reference current d n11 reference frequency Test Run: Page 62 Chapter 4 Setting Override Data If 0 is set in n06 multi-function input selection 1bits 4 to 7 are used to set override data.
Chapter 5 To prevent this, increase acceleration time or reduce load. Perform a no-load test run and an actual loading test run to check the direction of motor rotation, speed, omrno output cur- rent. Chapter 2 Digital Operator Data display section Monitor item indicators In-service item indicators green indicators Display These items can be monitored or set even section during operation.
Omron SYSDRIVE 3G3EV User Manual
Table of Contents Chapter 1. Operable Error status 0: Got it, continue to print. Frequency detection output frequency When the Inverter is stopped, all items can be monitored and the constant for each item can be set.
Motor capacity should be also increased. If the power supply for the main circuit is to be shut off because of the sequence, a mag- netic contactor can be used instead of a molded-case circuit breaker. Check the cause of the error, take the necessary action, and perform fault reset or turn the power off, then on.
If voltage is applied to the output terminals, the internal mechanism of the Inverter will be damaged. First, start the motor through the Digital Operator without connecting the motor to the mechanical system. Page 82 Chapter 7 Appendix A 3. Chapter 3 Design Note 1.
You should assume that anything not described in this manual is not possible. Surge arises when the motor inductive load is connected to the output side of the Inverter.
Stopped item indicators red indicators These items can be set only when the Inverter is stopped. Page 35 Omro 4 Preparing for Operation H Function of Each Component D Display Sections Data display section Reference frequency values, output frequency values, output current values, constant settings, and error codes are displayed.
When warning status arises, no error code is output.
Note that this warning is applicable whenever you perform any task after turning the main circuit off. During operation, only the items in the in-service item indicators section can be monitored and the constants for these items can be set. For the 3-wire sequence, refer to the wiring on page Chapter 4 Name Description Multi-function output 2 This function is set in n Don’t show me this message again. Monitor item indicators When this indicator is lit, an output frequency value Hz is displayed in the data kmron section.
The RUN and ALARM indicators on the front panel indicate the current Inverter sta- tus, and the data display section omfon displays information about an error that has occurred. The product contains potentially dangerous parts under the cover. Although care has been given in documenting the product, please contact your OMRON representative if you have any suggestions on improving this manual.
To prevent this, ad- just the carrier frequency according to the following standards: Table of 3gev Add to my manuals Omrob. Chapter 7 Appendix A 3.
The surface temperature of the Inverter may reach 30 C higher than the ambient tem- perature. Eliminating the cause recovers the system automatically. Well, what if you were able to see a piece of equipment before you purchased it?
OMRON 3G3EV-ABCUE – In Stock, We Buy Sell Repair, Price Quote
Chapter 5 The standard interval for regular maintenance is as follows: Same as for n06 input selection 3 Multi-function compact inverter sysdrive 3g3mv series pages.
Buying used equipment doesn’t always have to be a shot in the dark.
Therefore, constant numbers can be confirmed easily. Omro 31 Chapter 3 Design D Wires to be Used Always use twisted-pair shielded 3g3evv to prevent malfunctions due to noise. To print the manual completely, please, download it. Example Indi- Description of data cator display Output frequency Chapter 4 Note 2. Page 60 Chapter 4 Word no. Monitor item indicators When this indicator is lit, an output frequency value Hz is displayed in the data display section.
S Use metal box and piping. Chapter 5 Operation To reverse the direction of rotation, switch the wires of two phases of U, V, and W as shown below.