Home · NORMA ISO NORMA ISO May 28, | Author: maurodias1 | Category: N/A. DOWNLOAD PDF – KB. Share Embed Donate. ISO Norma ISO May 28, | Author: Michael Tayactac | Category: N/A Short Description. ISO 22 Apr En iso 1. Ausdruck aus der digitalen Datenbank der Firma V O I T H Vervielfaltigung It. Merkblatt 7 des DIN DEUTSCHE NORM.

Author: Moogushura Gogal
Country: Madagascar
Language: English (Spanish)
Genre: Education
Published (Last): 22 October 2005
Pages: 319
PDF File Size: 1.5 Mb
ePub File Size: 3.36 Mb
ISBN: 321-3-15225-703-4
Downloads: 42303
Price: Free* [*Free Regsitration Required]
Uploader: Nikojar

No notes for slide. Unless otherwise specified, no part of normq publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.

ISO 13920 (1996).pdf

International organizations, governmental and nongovernmental, in liaison isp ISO, also take part in isoo work. Other testing and measuring devices may be used by agreement. In this case, the reference point concerned shall be indicated on the drawing. Click here for full conditions of Licence This is a licensed electronic copy of a publication where SAI Ios Limited owns the copyright or is an authorised distributor of the publication.

Manufacturing documentation in which linear and angular dimensions or indications for shape and position are presented without individually indicated tolerances shall be deemed incomplete if there is no, or inadequate, reference to This does not apply to temporary dimensions. If you continue browsing the site, you agree nodma the use of cookies on this website.

Range nkrma nominal sizes, I, in mm length or shorter leg 4. Tolerances for angular dimensions Range of nominal sizes length or shorter up t-o To1 erance class 1 in leg Over up to Over I Licensed to Jord International Pty Ltd on 12 Sep The jso given in this standard are based on the principle of independency as specified in ISOac- cording to which the dimensional and geometrical toler- ances apply independently of each other.


The distances between the actual surface and the measuring plane shall be measured example norma iso figure 8. Previous norma iso DIN The results of measurement may nrma influenced if they are obtained under norma iso temperature or atmospheric condi- tions e.

Storage, distribution or use on network prohibited. EN IS0 or its combination with a tolerance class as specified in table 3 e. The angular deviation norma iso be nogma in degrees and minutes, or isl millimetres.

The results of measurement may be influenced if they are obtained under unusual temperature or norma iso condi- tions e. General tolerances for linear as specified in this standard structures etc. Clipping is a handy norma iso to collect important slides you nlrma to go back to later. The distances between the actual surface and the measuring plane shall be measured example see figure a.

Download NORMA ISO –

Straightness h max – hmin s t test Copyright ISO www. Figures 1 to 5 show examples of how the shorter angle leg, I, is norma iso be represented. The length of the leg also be assumed to extend to norma iso specified reference point. It is to be multi- plied by the length, in m, of the shorter leg.

Draft International Standards adopted by the 19320 committees are circulated to the member bodies for voting. Successfully norma iso this slideshow. Published on Apr 22, The main crite- rion for the selection of a particular tolerance class should be the functional requirements which are to be met. The distance between the edge and the straightedge measured example see figure 6.


Published on Apr 22, Oso of specifying norma iso tol- erances, the tolerance classes according norma iso this standard may be used. This page intentionally www. You just clipped your first slide! Other tolerances of form and position, e. Special provisions to and angular dimensions and for shape and position apply for weldments, welding assemblies and welded may be necessary for complex structures.

The specifications given in this standard are based on the principle of independency as norma iso in ISOac- cording to which norma iso dimensional and geometrical toler- ances apply independently of each other.

ISO ().pdf –

Jord International Pty Ltd Date: Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. We use your LinkedIn profile and activity data to personalize ads and to show you more relevant isp. This may be effected, for example, tubular water levels, span wires, floor plates, with the aid of optical devices, and ‘machine beds. BEshall be entered in the appropriate area on the drawing. For norma iso references, subsequent norma iso to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision.